How To Make A Silicone Mold For Resin Or Clay

How to make a silicone mold

If you’ve wondered how to make a silicone mold, the good news is that it’s easier than you might think.

All you need to use is two-part silicone mold putty.

Here’s why it’s THE BOMB to make a silicone mold:

✅ You don’t need any fancy equipment.
✅ Molds are food safe.
✅ You can have a ready-to-use mold in 30 minutes

Step 1: Prepare your work surface.

Make sure your working surface is clean. Cover it with a wax paper sheet, then tape it so it won’t move.

Step 2: Get everything ready.

Once you start mixing the mold putty, you must be ready to use it. That means having the items you’re molding ready as well. Be sure they’re clean and free of any grease or dirt. If you don’t, that will transfer to your silicone mold.

⭐️ BONUS:  If you aren’t sure what to use for your model, check out this mold-making article.

Step 3: Measure and mix the putty.

This putty mixes one part A with one-part B. You can ‘eyeball’ equal amounts of putty to mix it. You can also measure the parts by weight if you have a scale.

💡 Pro tip: It’s pretty forgiving when it comes to mixing. I’ve never used a scale to mix it, and my silicone always cures perfectly.

Once you measure the two parts, smash them together until they are evenly mixed. This takes about 1 minute. The putty is mixed when the color is even throughout. You shouldn’t see any streaks.

You only need to mix enough molding putty to cover and surround the item you’re molding.

💡 Pro tip: I usually only mold one thing at a time instead of mixing a bigger batch for a few items.

Step 4: Press the putty around your model.

Once you’ve mixed your putty, roll it into a ball bigger than your model. Flatten the ball slightly, then place your model into the flattened area. Roll the putty over the object until it’s covered, pushing in somewhat on the sides and corners.

Don’t push too hard. You want to leave putty at least half to three-quarters inches thick around all sides. If you don’t, it can rip when you demold your item.

💡 Pro tip: Use a Popsicle stick to push on the sides and flatten the bottom of the mold. This lets your silicone mold sit level when you pour your epoxy resin into it.

Work quickly. You only have about two minutes to mold the putty around your model once mixed. After that, the silicone won’t be workable anymore.

Set your mold putty aside to cure for 30 minutes.

Step 5: Demold.

Remove your model from the mold by pushing the sides to loosen the template from the mold walls. After a few pushes, your model should pop out easily.

Your mold is now ready for polymer clay and epoxy projects. The molds are also great for soap or candle making. You can also make molds for food projects like chocolates, candies, and ice cubes.

💡 Pro tip: You want to use a casting resin in your mold to get the best bubble-free results.

Want more help on how to make a silicone mold?

This video, courtesy of Meredith of Cosmic Designs, shows you how to make a simple silicone mold that’s ready to use in 30 minutes.


 

You can also see how to use two-part silicone putty to make a lego mold.

Ready to craft with resin but worried about making mistakes?

I’ve been there. I made so many mistakes when I started that I wondered if I would ever make anything I could ever sell.

It’s why I wrote the ebook Resin Fundamentals.  I’ve taken my sixteen years of resin experience and condensed it into an PDF book you can read this afternoon. It’s the book I wish I had when I started creating with resin! Buy the book now, and get a download link in minutes.

Unpublished Blog Posts of Resin Obsession, LLC © 2023 Resin Obsession, LLC

Like this post? You may be interested in  5 Resin Casting Tips Every Artist Needs To Know

11 thoughts on “How To Make A Silicone Mold For Resin Or Clay

  1. I learned a new technique from you. Your mold is really good. I like how you drop your putty ontop of your item. I was going the wrong way.

  2. I was going the other way too! I must try it your way, looks like you will get a better impression and mold… Thanks so much for sharing

  3. I really like how you did this but is there a way to make a mold of something you dont physically have? I want to make Kida’s necklace from Disney’s Atlantis only I dont have the physical shape of the crystal to mold with. How should I go about it?

  4. Cam,

    You can’t make a mold of something without a physical model. What I would recommend in this case is to find a wax carver (we can hook you up with one) to carve a model for you. You can then make a silicone mold from this wax model.

  5. Cam – It’s totally possible to make a mold without having a physical object. All you need is a 3D modeling program like Maya or Zbrush for your computer and enough skill in using it to create a 3D render of the object. Considering the simplicity of the crystal, it should only take about 30 minutes. Once the 3D render is complete, invert it. Then send the file to a place like Shapeways that does 3D printing. You can have a perfectly detailed mold delivered to you and ready for use within a couple days.

  6. I have a plaster (I think its plaster) of a sailing ship. It’s approx 22 inches tall, 18 inches wide and the highest point is approx 1 inch. It has some intricate details and the back of it is flat.

    I would like to make a silicone mold or other material that is suitable for epoxy resin. I want to make an export resin of this piece in other words

    I’m a total newbie with molds. Any pointers?

  7. I would like to make a mold and molding
    Using your products. I live in South Africa and would appreciate any help in getting the products here.
    Dave King.

    1. Hi Dave, we do ship products to South Africa when allowed. You will be given shipping options at checkout.

  8. Thanks for the article Katherine. I’m wondering if I can use an epoxy item as the physical model for my silicone mold?
    Background story: I created a free-form mold using silicone caulk, my resin item from that was a bit rough on the sides, so I dremmeled and sanded and polished and now it’s perfect. So I’d like to use that resin item to create a better mold for my future projects.

Leave a Reply

Your email address will not be published. Required fields are marked *

Subscribe to blog updates
Follow on Pinterest
Follow on Pinterest
Follow on Pinterest
Follow on Instagram
Follow on Youtube
Follow on Youtube