Resin Crafting Tips for beginners – resin beginner tips

Beginner tips and tricks for crafting with resin5 Tips and Tricks for Crafting with Resin!

This is a guest blog post by Mona Schmitt of

I loooove crafting with resin!  There are so many things you can do and experiment with and most of the time the results are fantastic!  Still things don’t always go as planned, but in life, they never do!  Here are some of my favorite resin crafting tips for beginners.

1.  Cold resin is bad.

I work in my basement and it tends to be on the cool side…all year long.  In the winter the heat rises to the upper floors and in the summer the cooled air settles right into my craft room.
I began using resin one summer before the air conditioner was on, and I was getting some great results.  I could not figure out why all of a sudden, a week or so later, I was getting bubbles.  Stubborn bubbles.  I could not pop them with my lighter, or by blowing through a straw.

seashell coaster

I searched the internet for answers.  Maybe I was mixing too quickly….probably true…. but it hadn’t mattered a week ago!  Finally, I found some suggestions about keeping your resin warm…hmmm.  Put your resin bottles in warm water before working with them.  Another trick is to keep the bottles, with water in a small crockpot (brilliant!) to warm them up.  I did start putting my resin bottles in a small bowl of warm (not hot) water for about 10 minutes before using them and it did the trick!  I did that for quite a while.

The problem with that method is the water.  Water and resin don’t mix.  A few times, I did not wipe the bottles off well enough and ended up dripping the water in the resin.  Also, at that time, I was using my homemade coaster mold, with the parchment paper.  Parchment paper is great unless it comes into contact with water.  Then it wrinkles and messes up my coaster.  There had to be a better way.

It occurred to me, I have a small heater under my desk and it keeps my toes toasty.  Why couldn’t it keep my resin toasty too?  That’s when I began putting my resin bottles, about 2-3 feet away from my little heater.  Close enough to warm them up, but not too close to make them too hot to handle.  Just remember, warm is good, hot is bad.  So, I warm up my resin bottles and my resin is thinner.  It mixes better (I still mix too fast).  I still get bubbles, but they are tiny, rise to the top, and pop easily with my lighter!

2.  Be smart.

Remember you are working with chemicals.  It is a great and fun medium to work with but make sure you have good ventilation and work with gloves.  I was told Nitrile gloves are better than latex.  It’s just smart, but it also beats trying to get all that sticky stuff off your hands!

resin crab

3.  Cleaning up a sticky mess.

You will have spills.   You will get mixed resin and unmixed resin on surfaces they should not be on.  Something will be unexpectedly sticky and you may not have any idea how it got there.  Not to worry, rubbing alcohol.  Get a big bottle of rubbing alcohol and keep it on hand.  Use it with a paper towel for large messes and use it with a Q-Tip for small messes or mistakes or drips in a mold you are working on.


4.  Plan ahead.

Think about the project you will be working on and have all the items on hand.  Have your molds ready, your psychedelic coastergloves, your stir sticks, mixing cups, whatever you are planning on putting in your resin, etc.  In addition to the project you are working on, have an extra mold handy.  Whether it be a jewelry mold or a coaster mold, if you happen to have extra resin, don’t let it go to waste.  I have made a bunch of jewelry pieces with resin I happened to have leftover.  I even made a coaster with multiple leftovers!


resin ball

5.  Experiment and have fun.

Don’t stress about something if it doesn’t come out perfectly!  I like trying to put new things in resin, especially in layers.  I like trying molds that weren’t made for resin.  Try some unexpected ideas.  Do what makes you happy!
I hope you have fun trying different things with resin and I hope some of my tips come in handy!

Remember Resin Obsession offers a variety of molds and resins to try!

If you want to see my crafts (resin and non-resin), go to

You can find me on YouTube, Facebook, Pinterest, Twitter, Instagram, Tumblr, Roku, just about anywhere.  I love to share even more resin crafting tips for beginners!

Happy Crafting!


Want to learn more resin crafting tips for beginners?  Then grab your copy of Resin Fundamentals.  This downloadable PDF book teaches the essential details resin beginners need to know to successfully create with resin!

Unpublished Blog Posts of Resin Obsession, LLC © 2020 Resin Obsession, LLC

Like this post? You may be interested in  How to dry flowers with silica gel beads

6 thoughts on “Resin Crafting Tips for beginners – resin beginner tips

  1. I started working with resin last year. Some mistakes of course. If I make a mistake, it becomes a magnet for the refrigator or a charm for a key chain. I don’t waste them either.
    I like the idea about using as samples for customers to touch and try on.

  2. Hi, I made some pressed flower resin jewelry main side is clear and So, when I flip it over after pouring resin, it’s not shiny underneath.How can I make it shiny and clear.

Leave a Reply

Your email address will not be published. Required fields are marked *