Wood and resin jewelry – Combine wood and resin

how to make wood and resin pedants

How to make a wood and resin pendant

by Michele Rober

Hello again! So today I will be showing you all how I create wood and resin jewelry. These resin pendants are easily my most talked about item at craft shows. They require power tools and a lot of elbow grease, but the result is something people are always in awe of. There’s a lot to cover in this tutorial, so let’s just dive right in!



all the supplies needed for creating resin wood jewelry

Resin Supplies Needed

-Square Mold
-Mold Release
-Clear Resin
-Mixing Cup
-Tree Wood Slice
Resin colors
– Lots and Lots of Sand Paper (80, 150, 250, 800, 1000, 1500, 2000 Grit)
-Table Saw (not pictured)
-Belt Sander (not pictured)
-Eye Hook
Necklace Chain


-Power Drill
-Super Glue
Resin Polish (not pictured)
-Soft Cloth (not pictured)


empty resin mold on table being prepared for use

So like I stated above, my mold is a 7 inch square plastic mold but if you have a mold similar in size and depth (at least 1 inch deep), then feel free to use what you have. Before starting, I pre-condition my mold with some mold release being sure to cover the whole surface area. Let this dry before pouring resin into the mold. This step can be omitted if you have a silicone mold. The brand I am using is Castin’ Craft.


Note:  You could work with a different size, either larger or smaller, for this project.  I simply find that 7 inches square is what works best for me.



slice of wood with measurements for cutting drawn on and a ruler and a pencil

Let me start this step with a little advice.

If you are going to buy your wood from the craft store (I got mine for $6), here are some tips on picking a good slice:

-Look for a piece with noticeable age lines (some are too bleached).
-The more ridges in the bark, the better!!
-Pick a piece that isn’t too thick.  About 1″ thick will be the easiest to work with.

After you pick the perfect slice, it’s time to measure out your cuts. If your mold is 7″ squared then you want the woodcuts to be equal or less than 7″ wide so that it fits into the mold. You will notice that I divided mine into four cuts, leaving a square in the middle, this is because I want to get as much use out of the bark as possible.  The bark adds special details to wood and resin jewelry.



hands holding slice of wood and cutting it with a dremel moto saw

Now that you have your cuts drawn out, its time to take your wood to the table saw. I’m using a Dremel Moto-Saw that I found for about $60. Some tips I have for using this particular table saw is to hold the wood firmly to the tabletop and go very slow to get straight cuts. I will admit that my cuts are always wavy and curved, but in the end, it really does not make a difference because it will all be sanded down.

five cuts of wood on a table


three cut pieces of wood in a square resin mold

In this step, plan out where you will be placing your wood in your mold.

There are three things to keep in mind when placing the wood:

-How big you want your wood and resin jewelry pendants
-Whether you want wood on both ends of the pendant
-What shapes you want to get out of the pendants.

There is no right and wrong way to place the wood just as long as you ALWAYS place the bark side of the wood toward the inside of the mold.



three pieces of cut wood in a resin mold with small plastic bottles used as weights

Once you have an idea of where you want to place the wood, remove it from the mold and mix up approximately 1 1/2 ounces of resin (based upon this size mold and the amount of wood I used). Pour it into the bottom of the mold and make sure it covers the whole surface.

Then, place the wood back into the mold where you had planned. This is a step I initially did not do when I first started making these pendants, but what I noticed happening is I would do a large pour of resin and the wood would float to the top and change positions. I set some “weights” onto the wood and let it cure for twenty-four hours.



resin mixture in plastic measuring cup with wooden stirrer and resin dye on a table


resin mixture in a cup with wooden stirrer with droplets of lavender resin dye


lavender resin mixture in measuring cup with wooden stirrer and lavender dye on table

Once you let the wood slices cure to the base of the mold, set it aside and mix up a batch of resin. I mixed a total of 6 ounces. This amount will vary based on how much wood you are using and the size and depth of your mold. Leave the mixture for about 5 minutes to allow larger bubbles to pop and smaller bubbles to surface so you can pop them by breathing into a straw.

Next, add your coloring! I use basic acrylic paint, but whatever you typically use to dye resin will work fine. I used 7 dots of color to achieve an opaque purple, but if you want something a little more translucent just add less color.



three cuts of wood and lavender resin mixture in square resin mold

Once your color is mixed up and bubbles are gone, it’s time to pour the resin into your mold. Pour slowly to minimize bubbles and be sure to pour into all the crevices to ensure the resin will distribute evenly across the mold. Let cure for at least 24 hours.

You might notice that I don’t fully fill the mold with resin.

I leave some of the wood exposed for a few reasons:

-It leaves a place to anchor down the wood to ensure it doesn’t float.
-I can save resin by not fully covering the wood.
-It ensures my pendant isn’t extremely thick and heavy.


three wood cuts in lavender resin and square resin mold

Releasing the resin from the mold is actually pretty easy. I pick up the entire mold and give it a little twist like I would an ice cube tray and then flip it over to push up on the bottom corner until I can grab it with my fingers to pull it the rest of the way out. YIPPIE! You have a block of wood and resin for jewelry!


pieces of wood in lavender resin with cut measurements drawn in pencil

Now here’s the thing, if you are a pro at using a table saw, then I suggest you draw out the shape and size of each pendant directly onto the wood. It will make your belt sanding experience so much better. But if you are like me, just draw out some lines on your wood that you want to use to approximate what you want your pendant to look like. There are no right or wrong cuts. You will see the belt sander will transform everything!


wood cuts in lavender resin being cut my dremel moto saw


four pieces of cut wood and lavender resin


left hand holding up wood and lavender resin shard


I am using the same technique as before when using the table saw, slow and steady. I only cut up a small portion of the block for demonstrating purposes, and I got 4 pieces out of it. So from the whole block, I will get about 10-12 pendants of varying shapes and sizes. As you can see, these are VERY rough cuts but pick your favorite and we will shape it into something beautiful using the belt sander!BELT SANDER TIPS:

central machinery belt sander

I feel like I need to go over a few things about the belt sander before you get going. This thing is very intimidating and can potentially be very dangerous. I have it set on the floor of my basement because I have more control sitting, but it should probably be placed on a sturdy workbench.

-Wear short sleeves and do not wear gloves! Lose clothes like sleeves and gloves can get caught and jammed into the belt sander, which as you can imagine would be extremely painful!
-Trim your nails. Yes, I have broken a nail by it scraping against the sandpaper and yes, it hurts.
-Wear goggles or glasses, dust will be flying all over the place
-Read the safety instructions of your belt sander for further precautions.

PS: My belt sander is from Harbor Freight and I am using 80 grit sandpaper.



holding wood and lavender resin shard on belt sander surface

holding wood and lavender resin charm on belt sander surface

Now that I have scared everyone, let’s begin shaping! My machine was off for the photos for obvious reasons but I wanted to show my hand placement when shaping. I always start by sanding down the face of the pendant first, so that the wood and resin are flush.

Hold the piece against the running belt being sure to have a strong grip, with your fingertips as far from the belt as possible. Once you have a flush pendant you can start shaping. Like before, have a strong grip, with your fingers safely placed. Always start with one edge and slowly lower the rest of the pendant towards the sander. You don’t want the belt to catch a corner and send your pendant flying across the room (yes, it happens). Try and make your pendant as symmetrical as possible, but just remember that your hand sanding will correct any slight mistakes.

Notes about using the belt sander for wood and resin jewelry pendants.  I use the belt sander dry. I have had no issues with the resin melting or getting soft on these larger pieces but when I shape and sand the face of the pendant, I do lift the piece off the sander often so that it doesn’t overheat. In other projects, I have had issues with the resin becoming soft, but these are so thick that as long as you wait a full 24 hours there shouldn’t be any issues (at least I haven’t had any.)

left hand holding up sanded wood and lavender resin shard



sandpaper grit 80 150 250 800 1000 1500 and 2000 on a table

As I stated in the supplies list, you need sandpaper grit 80, 150, 250, 800, 1000, 1500, and 2000.

Lay them out on your table in numerical order from smallest to largest as shown in the photo. This will essentially be your assembly line. The goal is to buff out all the scratches from the belt sander to return the resin to a shiny clear finish. I also set out a bowl of water because sandpaper grit 800-2000 should be done wet.



This step is pretty exhausting and takes at least 40 minutes to get through, but this is the final step before you make your pendant into a necklace. You are almost there! Typically I will spend about 2-3 minutes sanding per side at each sandpaper station. I have no specific technique, just quick back and forth movements. If at the end you notice there are tiny white scratches going through your pendant in certain spots, it just means you didn’t buff enough. When this happens to me, I start at grit 250 and go back through the rest of the paper.


left hand holding polished shard of wood and lavender resin

This step can be skipped if you decided to go for a more opaque color like mine. But if you chose to have some translucency to your piece then I would suggest polishing it. What I will do is dab some polish on an eyeglass cleaning cloth and buff it into the resin in circular motions. Try to avoid using it on the wood parts; sometimes it can slightly discolor it. Polish will not hide or get rid of any of the scratches left behind from the sanding but will make the resin shinier and more see-through.

I do not polish or seal the wood! This is something I have tried many times with different products to get a glossy look over the wood but it always comes out streaky or the wood absorbs the liquid. So in my process, for now, the wood stays unfinished after the sanding process.



left hand holding wood and lavender resin pendant with eyehook and chain

This step can be done in two ways. If you have wood at the top of your pendant where you want the necklace to dangle from, then it’s easy just to screw in the eyehook. Just keep twisting until it is flush with the wood. But if the top of your pendant has resin instead of wood, you will need to use a power drill to drill a small hole at the top. I will then use a little bit of diamond glaze super glue on the screw portion of the eyehook and place it in the hole you created with the power drill.


wood and lavender resin pendant on chain and in designer packaging

Enjoy your new wood and resin jewelry pendant!

What has been your experience making wood and resin jewelry?  Is this something you want to try?

Eager to learn more about making resin jewelry but overwhelmed with where to start?  It’s okay.  I felt the same way as a resin beginner!  It’s why I wrote the book, Resin Jewelry Making.  It gives beginners the vital details to make beautiful resin jewelry all from the comfort of home.  It’s the book I wish I had when I started creating with resin!

Unpublished Blog Posts of Resin Obsession, LLC © 2020 Resin Obsession, LLC


Like this post? You may be interested in  Resin in bezels - How to make a resin pendant using a bezel blank

60 thoughts on “Wood and resin jewelry – Combine wood and resin

  1. Thank you for doing this tutorial. I’ve been wondering how it’s done after seeing some similar ones on Pinterest. Really cool!

  2. Have you ever tried beeswax for the wood? It wouldn’t make it glossy but it would help condition and protect it.

  3. WOW how impressive. While looking thru the steps I thought that some of us who don’t have a saw could use some sawdust or smallish bits of timber and put it straight into jewellery resin molds. Must admit I do want to try the large slices of timber.

    1. Hello!
      Great idea! I have tried using cuts from thicker tree branches and while the look it different, it still makes for a unique pendant without the need for power tool investments.
      Thank you for reading!

  4. Thankyou for showing this , often wondered how it was done, hopefully I will get around to trying, the colours are
    beautiful Cheers Sandra

  5. Thank you for the tutorial! It’ll be fun to try this technique. One note: the saw you are using is a scroll saw, not a table saw. #toolnerd 🙂

  6. Hi, I would have assumed that the wood in the resin would need to be sealed with something like other items put in resin. But it sounds like you didn’t seal the wood at all? So you didn’t have issues with bubbles coming out of the wood or bark area into the resin? PS – Wow these are beautiful!! Thanks for sharing! c-

    1. Hello!
      I did not need to seal the wood before hand and I have had little issue with bubbles. This may be because I am using store bought wood, so it is possibly sealed with something already? Not quite sure.
      Thank you,

  7. it may also be because you’re not fully coating the wood in the resin- if you poured resin over the top of all the wood, the bubbles would float up to the resin covering it. …at least that’s my hypothesis. 🙂

  8. Great tutorial, thank you so much. I have 16 acres of woods surely I’ll find something out there to resin. Again thanks, great instructions.

  9. Your work is just beautiful and your instructions are clear and concise. After seeing this, I’m sure I can do it 🙂 You have taken the fear out of the process. Paula

  10. Great idea love the color! Have you tried using the mini wood slices? Just curious. I’m wondering if that would save a few steps? Can’t wait to try this. I have some gold flakes to add as well! Thank you!

  11. Thank you for taking the time to show us how you do your beautiful work.ive wanted to do this for so long but couldnt find any tutorials on it.

  12. Thanks for this informative tutorial…I had to laugh at the belt sander instructions. Yes! that thing is intimidating. I had a piece “go flying” and tore my basement apart looking for it, only to find it wedged under the disc sander later. Your pendants are beautiful. (I still have a lot of practice to do!)

  13. When you’re creating the base to hold the wood in place before pouring the rest of the resin mixture, are you doing just 1 1/2 ounce of the resin by itself or the full mixture of resin and gardener. I am just now becoming interested and wanting to try my first project.
    Btw these are beautiful and so easy to follow the instructions on what you’re doing. I was beginning to think this would be too difficult to try until i stumbled onto your tutorial!!

  14. Beautiful. Your tutorial is so clear. I appreciate your helpful hints. I never imagined I could be using my power tools to make gorgeous jewelry!

    I get my wood for free. I have gotten some very nice pieces from companies cutting down trees. So far, each tree service has been kind enough to give me the wood once I explained why I wanted it. One tree service even gave me their card and said I could have more wood slices when I need them. It never hurts to ask.

  15. Have tons on trees that were taken down at my house ! So do u soak the branch slices in borax? I would think you would have to because of bugs ? for Kathy P or whoever knows answer

  16. Hi,
    I ‘m new to resin and i wondered how these pieces were made
    Thank you for sharing!
    Before rushing out to buy new machines, would it be possible to do it all by hand?
    Do you sand down the side of the wood that touched the resin in the bottom?

  17. Thank you so much for this great set of instructions. Can you use a band or table saw to cut the resin? Will cutting resin
    dull the blade? Can you use a stop saw table saw to cut this resin? Again many thanks for this tutorial.

  18. MICHEL
    depuis un an je confectionne des pendentifs en bois précieux
    ébène,palissandre,racine de thuya etc (une centaine) je viens d’y incorporer de la résine crystal gédéo proportion
    1/3 durcisseur et 2/3 résine . dans votre tuto très bien détailllé vous écrivez proportion 11/2 mesure que je ne
    saisi pas ? pour l’équipement machines pas de problème
    j’ai tout ce que vous recommendez y compris un scie à chantourner Hegner . encore merci pour cette bonne marche à suivre

  19. Muchas gracias por tu tutorial y las explicaciones tán específicas en forma y tiempos, además de tús consejos. Realmente has hecho un gran trabajo 😊

  20. Hi Kathryn! I hope the world finds you doing well and healthy. This is so terrifying, living in this world has be one a world we can’t live in!
    Enough gloom. I love your work, totes & blog of all you share! The wood resin pieces are the main reason I’ve been interested in resin. They are just Gorgeous!
    Do you know of anywhere to buy pre fab wood pieces? Since downsizing all the big tools are gone!
    If you think of anyone, please holler back ♡
    Thanks for everything! Katy

    1. Hi Katy, I hope you are healthy and well too! I’m afraid I don’t know of any places to get premade wood pieces, but perhaps this is a good time to connect with another woodworker you may know of? S/he may be able to get you some small custom pieces to include in your resin project.

  21. I love this! I’m looking at buying a 2.3 amp belt Sander, do you think that will be enough to sand this project?

  22. I have recently become obsessed I
    with this process, using store bought wood slices to create wood and resin pendants. They are turning out beautiful (thanks to this amazing tutorial) but there is one problem I’m running into. Some of my pieces are breaking in the bark areas. I guess because the bark is so fragile. I don’t really want to coat them with anything because I like the natural wood look.
    Does anyone have advice on how to stop this from happening?

  23. Such unique designs of wood jewelry, especially the rings are very beautiful and unique. People who are looking for wood jewelry designs should consider this blog.

  24. I wondered how people got wood the same shape as the intended mold. I would never have guessed this method. Brilliant. So many questions answered and done in an easy to understand tutorial. I love working with power tools so this is going to be a blast. And I have access to all the free wood I can ever want. Can’t wait to get started. Thank you so very much.

  25. Hi I’m trying to start a resin pendant business and was just wondering if the water when sanding caused any swelling with the wood, I have done wood and resin pendants and it seems to separate the join (though I do go from 240 grit to 10,000) Was there an issue like this or not really

        1. Hmm. I wouldn’t expect that to separate from wood. It sounds like something in your wood might be acting as a resist and keeping the epoxy from fully bonding.

Leave a Reply

Your email address will not be published. Required fields are marked *